CSC Screen

Menu
Menu

CSC REi TECH WATER-BASED DIGITAL INK - ECOSOL E1 DTG 280 SERIES

Ecosol E1 DTG 280 White are another innovation of CSC for the motif impression sector with our new generic of non-PVC, non-Phthalate and Formaldehyde free high solid content, hybrid of waterbase thermoplastic acrylic with silicones which meets our E1 compliance.

DTG on dark fabric had always been difficult, common problem of DTG on dark using inkjet white are inkjet nozzle clogging, poor washing and crocking fastness. With our new Ecosol E1 DTG 280 White these problems will be history of the past.

Ecosol E1 DTG 280 White are hybrid high solid waterbase ink. Ecosol E1 DTG 280 White are excellent product for use in printing of high opacity underbase white ready for receptive of most inkjet ink for dark shade to light color fabrics where excellent finish, elastomeric and soft hand feel are required. Motive printed by DTG process colors on Ecosol E1 DTG 280 White will have excellent elastomeric properties, good washing fastness properties, good crocking properties and high color brilliancy.
Cotton, Blends Cotton Polyester, Polyester, Nylon and Stretchable Syntactic Fabric.

*ALWAYS PRETEST FASTNESS PROPERTIES BEFORE PRODUCTION.*
*STIR WELL BEFORE USE*

Ecosol E1 DTG 280 White are designed as receptor for generally broad ink droplets from 0.5 picoliter to 90 picoliter.

Base White
Ecosol E1 DTG 280 White is recommended to be use direct as underbase white for hybrid digital print.

Digital Over Printing
Overprint your digital design on the underbase Ecosol E1 DTG 280 White while ink are wet. No intermediate flash cure is required.

In certain occasion, mixing small dosages (2 to 5%) of Lubricant DP into the ink will be beneficial as this will reduce the ink evaporating rate or slow down the drying speed of Ecosol E1 DTG 280 White.

To achieve excellent opacity, elasticity on rib or stretchable fabric the below precaution are to be followed.
  • Always lay down higher deposit of Ecosol E1 DTG 280 White by using lower mesh count screen, rounded squeegee, and soft table.
  • Print Ecosol E1 DTG 280 White onto the stretchable fabric, following the direction of the fabric grain.
  • Over print your DTG Process colors while the inks are wet.
Printers are advised to use only water resistant, direct in direct emulsion.

Mesh Type
32/80T~52/135S mono-multi filament for under base white.
52/135s~120/305S mono-multi filament for detail and tone on fabric.
55/65 shore A Double Bevel: For excellent opacity on printing under base white.
65/75 shore A Double Bevel: For detail and fine toning effect.
For maximum fastness, Ecosol E1 DTG 280 White with over printing of Ecosol E1 DTG Process color are to be cure at 160ºC at 2000 cfm/55cmm for 90 seconds.
20 liters Ropac Pails : 25 kgs for White, 20 kgs for OP & 20 kgs for Clear.
200 liters Metal Drums : 250 kgs for White, 200 kgs for OP & 200 kgs for Clear.

*ALWAYS STORE INK UNDER SHADE AND AWAY FROM DIRECT SUNLIGHT*
Ecosol E1 DTG 280 White are completely green and fully comply with CSC E1 RSL list which meets the E1 standard of safety requirements, it is nonvolatile (waterbase) and was made from material that is non-carcinogenic and non-hazardous to the environment.

CSC E1 RSL list could be obtained upon request.
Always use Waterbase mode in using Ecosol E1 DTG 280 White on an Automatic press. Flood screen when every printing stroke are completed to prevent ink from drying on screen. Avoid using too high a temperature on flashing and make sure flash cure are air ventilated.
BACK